064AV......You need to back up the bus! You have a pic of an 046 case there, not an 064.
Poly flywheel saws use a different coil again.
Poly flywheel saws use a different coil again.
Stihl 064 Coils
- Thread starter mikefunaro
- Start date
Help Support Arborist Forum:
Like I suspected.....With that 064 case, you can use your 1201 flywheel with either of those coils you have pictured.
Was that the question??
Was that the question??
This isn't my post, but my question is can 064 timing be altered by mixing and/or matching flywheel and coil options. I want to advance my timing (I think). Move my flywheel clockwise OR move my coil counter-clockwise. Just an idea...
Last edited:
All the combinations I have seen that ended up with a "non-stock" timing, yanked the rope out of your hand and bit hard....:hmm3grin2orange:
If you want to experiment with altering the timing slightly, Get some extra keys and file the tops of them to make slight timing variations.....The key is just there to locate the flywheel until you torque the nut and lock the flywheel to the taper on the crank.
KTM640
ArboristSite Operative
Checki out hte PDF attached. I think this is what you guys are looking for..
Jon
Jon
wigglesworth
Booned
K guys...
Here is the "dog leg" 064 coil. This fits the early 064's like mine...
Here is the dog leg coil compared to the 1300 coil.
And here is the 1128 XXX 1309 coil mounted on my 064 using the 1201 FW. I cant tell any running difference between it and the original, but I aint put a watch, nor a timing light on it. The rear hole, obviously doesnt line up, but the bottom and top did perfectly.
And here is a good "what if" question....
What if one pressed the 1300 coil off the laminates, and flipped it? It appears to line up perfectly on the bottom lugs. Would the timing still be the same?
Here is the "dog leg" 064 coil. This fits the early 064's like mine...
Here is the dog leg coil compared to the 1300 coil.
And here is the 1128 XXX 1309 coil mounted on my 064 using the 1201 FW. I cant tell any running difference between it and the original, but I aint put a watch, nor a timing light on it. The rear hole, obviously doesnt line up, but the bottom and top did perfectly.
And here is a good "what if" question....
What if one pressed the 1300 coil off the laminates, and flipped it? It appears to line up perfectly on the bottom lugs. Would the timing still be the same?
johnfawn2000
ArboristSite Operative
mike got one on order from stihl,there were 3 updates. The part # all superceded or work for all 064's.i dont remember the # but is about 130.00.may want to ask for those numbers from dealer, or i can when i go back.hope this helps
glock37
Addicted to ArboristSite
99busa
ArboristSite Lurker
I'm looking for the same exact coil for my old school 064. None of the part numbers match up on any of the stihl tech pages, so have you found an actual part number for this coil? Thanks,
Which coil? Every coil has a part number and every one of those has been listed in the numerous threads regarding 064 coils.
99busa
ArboristSite Lurker
Hello Jacob J,
You guys tried to help me out a while back, and I wasn't able to provide pics that showed what my original coil was. I'm not trying to mess up this thread, but was excited to see a pic of a coil like mine, that has the middle hole offset farther down from the center of the coil, and also has the external small black trigger box. My coil has the part number Bosch
2 204 222 999 and my flywheel is part # 1122 400 1201a
Any help is very appreciated. Thanks
You guys tried to help me out a while back, and I wasn't able to provide pics that showed what my original coil was. I'm not trying to mess up this thread, but was excited to see a pic of a coil like mine, that has the middle hole offset farther down from the center of the coil, and also has the external small black trigger box. My coil has the part number Bosch
2 204 222 999 and my flywheel is part # 1122 400 1201a
Any help is very appreciated. Thanks
wigglesworth
Booned
U can subsitute that coil with the 3 legged 046 coil like I did, and just use the top and bottom holes. Works great....
Your coil is #1122 400 1300, the early one with the external trigger. You can do Wigglesworth's trick of substituting an 046 coil.
99busa
ArboristSite Lurker
Can i order that coil # 1122 400 1300 from stihl or is it not available?
It's not available anymore but there's lots of used ones around. I know one guy that has about eight of them.
They're mine!! All mine I tell ya!!!....Bwahahahahaha!!!:hmm3grin2orange:
Perhaps I've not looked in the right place, but my 066 and 064 coils have no numbers which I have found.
