sefh3
Addicted to ArboristSite
Ed,
Is that the smaller of the 2 styles? I have a new one from an non-pro 026. PM me if that will work.
Swap meet...
- Thread starter Four Paws
- Start date
Help Support Arborist Forum:
Ed,
Is that the smaller of the 2 styles? I have a new one from an non-pro 026. PM me if that will work.
sefh3
Addicted to ArboristSite
Yes, it's a small one, no extra hole in the back. Got one?
I think so, I'll look tonight for ya.
I definitaly have one for you if struggle doesn't...
Those things are hard to come by in good condition. I have 1 and it has zero flocking left. I had to pay $26 for the last one I needed... Next time I'm going the craft store and going to glue some felt fabric on the inside of the filter for $3... PS: I owe ya for the shine job on my jugs...
Anyone have some carb studs for a stihl 036pro? Evidently, I learned last night the 034/036 carb studs are shorter and don't allow the thicker pro AF to be screwed on...
Last edited:
That doesn't sound right... :msp_ohmy:
Glad you like em, I can't believe they got there that quick.
You don't owe me anything, only takes a few minutes to bead blast them.
I had posted a while back I was looking for a fuel tank assy for a Makita 6401 for a buddy of mine. We are still looking if anybody has a good one. Can be Dolmar red.
Trx250r180
Saw polisher
i have a little yellow saw here says eager beaver i may have these
TonyRumore
ArboristSite Guru
There are three styles. The standard 026 uses a filter that is taller than the 024 filter. It can be used on an 024, but you have to swap to the taller 026 air filter cover to clear it. The Pro 026 filter is tall like the standard, but it is also wider, running further to the left of the saw. It goes over the fuel tank vent, so you can't use the black tower vent with it. It also has the inteli-carb port in it.
The low profile 024 filter is fairly hard to come by on the used market. They rarely come up on e-bay.
o8f150
Tree Freak
michale34
ArboristSite Operative
024/026/028 project saw
im looking for a 024/026/028 project saw that me and my son can work on together. he likes working on 2 stroke so im try to help him.
im looking for a 024/026/028 project saw that me and my son can work on together. he likes working on 2 stroke so im try to help him.
o8f150
Tree Freak
get ahold of wigglesworth,, i was at his place yesterday and he had 2 of them that he was going to sell
michale34
ArboristSite Operative
thanks i just pm him
350jeepcj5
ArboristSite Operative
I gotta pull you a case bolt and a stop switch...been super busy trying to get the 2nd building done for fall/winter service :bang:
did you still need the muffler bearing?
You know I do, they won't run without it!
MechanicMatt
Cut Split Stack Burn
Im pretty sure wiggs had two 025's they were on here about 5 pages back. Take two and make one
ChainsawmanXX
Addicted to ArboristSite
Looking for 051 muffler an recoil!
Looking for 051 muffler an recoil!
I got one from an 052, will that work?
SawGarage
Addicted to ArboristSite
NOS work for you?
I think he's busy trying to find an 052 ipl. :hmm3grin2orange:
ChainsawmanXX
Addicted to ArboristSite
Im not sure.. you told me that your 009 cylinder would fit on my 090.. it didnt!! Just because you can switch the numbers to make them the same, doesnt mean the parts will switch around! :bang:
NOS work for you?
Why yes it would Mr.stranger!
Watch it! I have a whole trash bag filled with rubbers with your name on it!
Nasty.. i know
SawGarage
Addicted to ArboristSite
:bang:
Watch it! I have a whole trash bag filled with rubbers with your name on it!
Nasty.. i know
DUDE....c'mon....that's messed up... :msp_mad:
052... oohhh..which WAY did he go, George, which way did he go.... :monkey:
