Swap meet...

[thomas1]

I'm not sure what fits it. It's not really even worth researching.

All I know is that I picked it up for a 5 dollar bill and it has no hours on it. Needs a couple minor parts, cleaning and fuel lines.

I'm thinking I can get a few bucks for it once it runs.



Chris

Do it lookie like thees?

I have the adjuster screw also.

 

[mdavlee]

Needing an 028 super coil. Got the neighbors saw here and it cuts out when it gets warm. Mostly green paper to trade.

 

[ptjeep]

Need a starter assembly for a stihl 064. Got money to trade!

 

[redray46]

028 super coil

Needing an 028 super coil. Got the neighbors saw here and it cuts out when it gets warm. Mostly green paper to trade.

I may have one,will check the 028's parts saws tomorrow.
Ray

 

[mweba]

Nos 101 cover

dont tapatalk and drive


edit Well that didn't work! Who was looking for a 101 muffler?

 

[struggle]

Nos 101 cover

dont tapatalk and drive


edit Well that didn't work! Who was looking for a 101 muffler?

67L36Driver was looking for it

 

[mdavlee]

I may have one,will check the 028's parts saws tomorrow.
Ray

Ok thank you sir.:smile2:

 

[mp5n]

Looking for 066 parts

I’m looking for the following parts for a Stihl 066 Magnum bucket case I’m trying to resurrect:

1. Crankshaft, newer style P/N 1122 030 0408. This is the one for the poly flywheel. It’ll have the 10mm thread on the flywheel side.
2. Coil and basic wiring harness.
3. Clutch cover.
4. Recoil starter assembly.
5. Chain brake hand guard.
6. Intake manifold.
7. Impulse line.
8. Handlebar.

If anyone can help out please PM me with what you have and what you want. I’m currently cruising eBay, but would rather pay someone from this site.

Thanks in advance,
MP5N

 

[Mastermind]

I’m looking for the following parts for a Stihl 066 Magnum bucket case I’m trying to resurrect:

1. Crankshaft, newer style P/N 1122 030 0408. This is the one for the poly flywheel. It’ll have the 10mm thread on the flywheel side.
2. Coil and basic wiring harness.
3. Clutch cover.
4. Recoil starter assembly.
5. Chain brake hand guard.
6. Intake manifold.
7. Impulse line.
8. Handlebar.

If anyone can help out please PM me with what you have and what you want. I’m currently cruising eBay, but would rather pay someone from this site.

Thanks in advance,
MP5N

I have the recoil and a wide clutch cover.... PM scent.

 

[jimbo1490]

stihl coils

There's nothing special about that coil. It came on many many Stihl saws. One from an 029/MS290/310/390 034/036/MS360, 038 among others will work just fine so you need not confine your search to 028's.

Jimbo

I may have one,will check the 028's parts saws tomorrow.
Ray

 

[mdavlee]

I didn't know if that coil was used on anything else. I don't mess with many older saws so I'm learning about them as I go.

 

[ARsawMechanic]

I'm searching for a coil for my older Sachs Dolmar 115. From all the info, it looks like the 109, 110, 111, 115, & PS 540 will all fit it, but it CANNOT be the Ducati brand coil with the metal strap protruding from it. Bosch & Prufrex were the other brands (that I am aware of) that would work.
Thanks in advance!!

 

[Arrowhead]

Looking for a 36" +/- D196/D096 sprocket or roller bar.

 

[Roanoker494]

Looking for a couple cutting chains (prefer major brand non safety chisel or semi chisel)

3/8 X .050 X 80DL for a poulan bow bar
3/8 X .050 X 84DL for a stihl 24/25" bar
3/8 X .050 X 72DL for a Dolmar bar

Could also use a 3/8 sprocket for a Poulan 7700, or a rim sprocket system.

Also interested in "common supplies" like fuel line, 3/8 rim sprockets, chain presets and etc.

Could use a 5 3/4" x 3/16" x 3/4" chain grinding wheel, also wheels for other pitch chains.

I have Poulan 3800 parts. No fuel tank, top covers and the cylinder has ingestion damage. (Has the 4000 style starter pulley and flywheel)
AH47 parts
Mac 47 and 4-30 parts
Mac 35A powerhead or parts
Some Homelite 8800 parts
Maybe some other stuff

 

[timberdollars]

Partner P55

I am looking for a Partner P55, it needs to be a case/cylinder at min. I have lots of other Partners but need a real P55 saw, they are different by the T-port in the exguast outlet. Pull the muffler and look inside if theres a slot on the roof of the port its good. Also there will be "1" round hole on the bottom of the saw for the oiler, not a bolt and cover as found on others.
And will be yellow
I want a complete saw but a case will work to start.

trades/worthless green stuff

 

[sachsmo]

I'm searching for a coil for my older Sachs Dolmar 115. From all the info, it looks like the 109, 110, 111, 115, & PS 540 will all fit it, but it CANNOT be the Ducati brand coil with the metal strap protruding from it. Bosch & Prufrex were the other brands (that I am aware of) that would work.
Thanks in advance!!

There is an ugly looking parts saw (115) on the bag right now. Should go cheap, but you never know over there.

 

[ARsawMechanic]

There is an ugly looking parts saw (115) on the bag right now. Should go cheap, but you never know over there.

Yeah, the one that got run over by the barn? I'm watching it, it'll probably fetch $100 plus in that shape!! :msp_rolleyes:

 

[kyle1!]

026 fastners

I just picked up a parts 026 that is missing every screw and nut. Stihl will probably want a few $$$ for new ones so I ask here. Also need the handle cover.

Replace the rubber bits and seals and it should be a runner.

Also I am sure I have the wrong Stihl flywheel puller. Will the one for the 056 work on a 026? If not can I trade someone for the correct one. I know long shot umpkin2:

thanks Brian

 

[tmessenger]

Lombard Lighting

A friend of mine has a saw shop that his grandpa started back in the late 60's well he found and bought back the first saw they sold out of the shop a Lombard Lighting 4.2 cu in.

He's looking for a piston and cylinder for it so they can get it back up, they have loads of old parts and $.

 

[Chris J.]

As y'all know I've been looking for parts for a Jonsered 2095. Below (hopefully) is a link to photos of the saw; obviously I'm needing just about every fastener.

Jonsered 2095 chainsaw pictures by antoniosalieri - Photobucket