the all aussie dribble thread!

[derwoodii]

Thanks fellas for that phone info a few weeks ago,
i ended up going Samsung galaxy ace +,i got the patch lead as well, trickiest part was putting the hole in the back cover,now I have service and net where I never thought I would with these newer phones:msp_thumbup::msp_thumbup:

dear wife just got a Samsung Galaxy she found the tricky part was just getting the back cover off :msp_sad: after that its been a big learning curve much cussin n frowns. Daughter no1 has been a help as she runs one as well

 

[splitpost]

hay guys need some help my 42" bar for my 084 and 880 i run 404 chain how many DL is it ???
i have the bar and only chain on it and its too much of a pain in the ass to take of to count so can yas be nice and tell me how many DL it is :biggrin:

I got an Oregon powermatch bar on mine and it was .404 =122DL ,I changed the tip to 3/8 and now its 134 DL

 

[splitpost]

dear wife just got a Samsung Galaxy she found the tricky part was just getting the back cover off :msp_sad: after that its been a big learning curve much cussin n frowns. Daughter no1 has been a help as she runs one as well

sounds familiar:biggrin:

 

[bennn*e]

hay guys need some help my 42" bar for my 084 and 880 i run 404 chain how many DL is it ???
i have the bar and only chain on it and its too much of a pain in the ass to take of to count so can yas be nice and tell me how many DL it is :biggrin:

123dl

 

[bezza1]

I got an Oregon powermatch bar on mine and it was .404 =122DL ,I changed the tip to 3/8 and now its 134 DL

thanks mate got some slabbing to do for a mate big log he said don't know what it is havent seen it yet will get some photos for yas all i think i will go do it next wekend

 

[bezza1]

123dl

sweet as thanks bennn*e
i think this bar is a GB its been re pained before i got it ill be running stihl chain on it
what do you guys say semi chisel or super for slabbing ?? and do you think 10deg is best ???

 

[MCW]

what do you guys say semi chisel or super for slabbing ?? and do you think 10deg is best ???

Semi Chisel/ripping at 10° for sure. 30° etc also does a good job but doesn't leave as nice of a finish as the 10° angle.

 

[bennn*e]

sweet as thanks bennn*e
i think this bar is a GB its been re pained before i got it ill be running stihl chain on it
what do you guys say semi chisel or super for slabbing ?? and do you think 10deg is best ???

I have never slabbed my self so I don't claim to know anything about the subject but I sell 46RCX to a client so slabs with a lucas mill. It is .404 chipper chain at 10' standard sequence. he removes anywhere between 3, 5, or 7 teeth and between a pair of cutters to help with chip clearance

Carlton make .404 full chisel with a factory 10 tooth or dl spacing I can't remember now and Oregon make a similar version to RCX but I priced it once and it was stupidly expensive

 

[MCW]

Carlton make .404 full chisel with a factory 10 tooth or dl spacing I can't remember now

Correct old son. One pair of cutters every 10DL.

Brace yourselves...

B3RM10-100RSPRSK

 

[splitpost]

sweet as thanks bennn*e
i think this bar is a GB its been re pained before i got it ill be running stihl chain on it
what do you guys say semi chisel or super for slabbing ?? and do you think 10deg is best ???

Semi Chisel/ripping at 10° for sure. 30° etc also does a good job but doesn't leave as nice of a finish as the 10° angle.

I mill purely for building materials ,30 deg gets the job done faster but the finnish isn't as good,i use 36RM

 

[460cixy]

File handle

I used one of these on the weekend best file handle ever GA98A, Handle, File

 

[MCW]

I used one of these on the weekend best file handle ever GA98A, Handle, File

Now you've done it. I've been looking for a decent file handle for bloody years that doesn't end up wearing out. Bravo old chap...

P.S. I assume it will clamp down small enough for a chainsaw file?

 

[460cixy]

Fits a 3/16 file ok when I used it any snap on rep should have them

 

[ausneil 1]

I used one of these on the weekend best file handle ever GA98A, Handle, File

what's wrong with an old corn cobb or a valve stem from a tubeless tyre...?????? See all kinds of holders in farmers sheds and of coarse they all work. (according to them)
Many bushmen have cut off a little green limbs and use that.

I still like the old Oregon wooden holders that came out years ago, they were good, some of the cheap plastic stuff is barely there tho and some are all but useless especially when you have to pack the hole so a small file doesn't fall out.

My completely useless words of wisdom for today, have a nice day men.

 

[460cixy]

I have a husky file holder that locks on to the file pretty good

 

[Gologit]

Can anybody give this guy some iinformation?

http://www.arboristsite.com/employment-forum/241785.htm

 

[460cixy]

http://www.arboristsite.com/employment-forum/241785.htm

I can't help the bloke but that's the sort of immigrants we need ones willing to work

 

[Gologit]

I can't help the bloke but that's the sort of immigrants we need ones willing to work

Yup, he sounded alright so I thought I'd put it out there for you guys.

 

[ausneil 1]

http://www.arboristsite.com/employment-forum/241785.htm

Bob, I will send him some email addresses later after work, I know quite a few business who may give him a go or maybe steer him to someone who will.

Your dead right Matt, immigrants who will work are the ones we want if we are going to except them.

 

[Gologit]

Bob, I will send him some email addresses later after work, I know quite a few business who may give him a go or maybe steer him to someone who will.

Your dead right Matt, immigrants who will work are the ones we want if we are going to except them.

Good on ya Neil. The guy sounds like he wants to work. Down there or up here...we'll take every one of those that comes along.