The made in north america Old Magnesium Swap Meet.

[Eccentric]

Must've been a noodlin' fool with that custom "clutch cover" too.

 

[eiklj]

Could you hook me up with a bow bar & chain for my Super Sexy 75? And maybe the right side bar cover/oil tank/starter assembly?

 

[AU_K2500]

OIL AND GAS CAP for HOMELITE EZ AUTOMATIC...Bueller.....Bueller?

 

[Mr. Bow Saw]

Could you hook me up with a bow bar & chain for my Super Sexy 75? And maybe the right side bar cover/oil tank/starter assembly?

What do you have 7/16 or 404?
I can't do anything with 7/16.

 

[bplust]

Just found an oddball item in a box of parts I bought

(Homelite) part# 55593-3
(Windsor) part# HO-36-D8

1/2" pitch 8 tooth gear

Fits Homelite 6-22, 7-21, 7-21C, 700G, 770G, 707G, 775G, Super Whiz

It's used, but in good condition.

If you're interested, PM with an offer. I don't have any saws or chain that'll be happy with this.

 

[eiklj]

What do you have 7/16 or 404?
I can't do anything with 7/16.

Can't know for sure until I pop the clutch off but appears to be a .404 spur sprocket.

 

[jerrycmorrow]

Somebody asked me about the C5 parts so i took some pix in the dark..

you still got this C5? if so, whatcha want for it?

 

[bplust]

If you're interested, I have a 1/2" pitch 8 tooth drive gear and a bucking spike for that C-5 there and other C-series saws.

 

[RandyMac]

If you're interested, I have a 1/2" pitch 8 tooth drive gear and a bucking spike for that C-5 there and other C-series saws.

1/2" sprocket? Got a pic, part # and dimensions? I need one for a 5-20

 

[jerrycmorrow]

If you're interested, I have a 1/2" pitch 8 tooth drive gear and a bucking spike for that C-5 there and other C-series saws.

whatcha want for the spike?

 

[bplust]

My bad, it's not for the C-series, I accidentally threw it in the same bin as the C-series stuff.

Here's the info:

(Homelite) part# 55593-3
(Windsor) part# HO-36-D8

1/2" pitch 8 tooth gear

Fits Homelite 6-22, 7-21, 7-21C, 700G, 770G, 707G, 775G, Super Whiz

It's used, but in good condition.

Picture will take a minute, camera needs to warm up, I left it outside.

Bryan

 

[Jacob J.]

1/2" sprocket? Got a pic, part # and dimensions? I need one for a 5-20

Randy-

I'm pretty sure I have one you can have.

 

[Homelite410]

SXL925 coil bracket

I am looking for a later sxl925 1 piece solid state coil bracket which makes up flywheel side case cover and bearing holder. Have green paper to trade..

 

[dff110]

Remington Stuff

I'm looking for a starter, and starter cup for a Remington PL-5. Also, in need of one of the plastic snap on air filter covers for the Remington Mighty Mite.

I had 3 Mighty Mites, and made 2 good ones. So still a few parts left over if it would be of help to someone. I know it's a very common saw. I guess everyone just broke those air filter covers haha.

 

[CM76]

Looking for complete or semi complete 7-29 / 8-29 Homelite belt drive saws.

I have large capacity McCulloch bits / saws to trade

Throwing this out there because I love them!

Regards,

Chris.

 

[67L36Driver]

I'm looking for a starter, and starter cup for a Remington PL-5. Also, in need of one of the plastic snap on air filter covers for the Remington Mighty Mite.

I had 3 Mighty Mites, and made 2 good ones. So still a few parts left over if it would be of help to someone. I know it's a very common saw. I guess everyone just broke those air filter covers haha.

I'll have a leftover starter cup when I get my latest PL-4 put together in the next couple days. But, cannot help on the recoil starter parts except for a cover, dog and pulley.

The PL-5 parts saw was devoid of starter parts.

What I don't have, is the pair of fiber washers, preload spring, flat washer and 'E' clip to make a complete starter.

 

[67L36Driver]

The above PL-5 parts saw has a passing fair cylinder and piston if anyone needs them.

Not real good but with new rings should make good compression.

Make a PL-5 out of a PL-4 as the piston cylinder bolts right on.

 

[dff110]

I'll have a leftover starter cup when I get my latest PL-4 put together in the next couple days. But, cannot help on the recoil starter parts except for a cover, dog and pulley.

The PL-5 parts saw was devoid of starter parts.

What I don't have, is the pair of fiber washers, preload spring, flat washer and 'E' clip to make a complete starter.

On my pl5 the spring loaded clips are worn off, and all the groves are worn away in the cup. Can I just file new groves into the cup? If not, I would be interested in yours.

 

[67L36Driver]

On my pl5 the spring loaded clips are worn off, and all the groves are worn away in the cup. Can I just file new groves into the cup? If not, I would be interested in yours.

When it is working correctly, you shouldn't even need grooves in the starter cup. The dogs will slide out to engage in the first 90 degrees of pulley rotation. Seldom do the dogs actually wear as a lot have been filed and bent to make them 'engage better'. The trick is to have the mechanism put together correctly with no oil on the fiber washers. One on each side of the dog assembly. Pressure from the spring and friction of the washers hold the dogs stationary as the pulley turns so they slide on the posts and extend out.

 

[dff110]

Thanks for the information. I will try that and see if it works