grounded switch
The made in north america Old Magnesium Swap Meet.
- Thread starter 67L36Driver
- Start date
Help Support Arborist Forum:
Fuel cap repair.
Chainsawlady has the duckbills and sintered bronze filters for the Homie fuel lids. Takes less than five minutes to fix the problem. I fixed four.
Chainsawlady has the duckbills and sintered bronze filters for the Homie fuel lids. Takes less than five minutes to fix the problem. I fixed four.
AU_K2500
NSM
No continuity through the switch. Replaced it with one from another homie parts saw (C51) and it fired right up on the 4th or 5th pull.
Anyone have a 42"+ roller nose bar to fit a Homelite 450-750, XL800-900 series and etc??
Those bars are tough to come by. Best of luck for you Johnnie.
AU_K2500
NSM
Looking for a Homie C series Air filter And Misc. Hardware for a Homie Super EZ auto.
And a rubber rear handle grip for a Super EZauto
And a rubber rear handle grip for a Super EZauto
What all do you need for the EZ? My parts saw is pretty much complete.
I have a 82cc XL-800 top end here that may work, the piston has some marks but it was producing good compression. Anyone here know for sure if it would work or not?
AU_K2500
NSM
pretty sure its magnesium, and i know its old....
Anybody got rings for an old MAC 3-25. dont know how common the bore size was. its a 2" bore and i can mic. the rings for thickness.
Anybody got rings for an old MAC 3-25. dont know how common the bore size was. its a 2" bore and i can mic. the rings for thickness.
Eccentric
Mister Wizard
I believe it'd work so long as you swapped them over as an assembly.
I've seen 3-25 rings on feebay recently. Alternatively, you can get rings from Otto Gas Engine Works or Hastings. They can make up a set of rings to your specs, and they're reasonable.
Looking for one or more fuel tank vent/check valve for Remingtons. #65708
Looking for 60's front tank large McCulloch starter assemblies (250, 380, 550, 450, etc. etc.). I need a few.
Have some stuff to trade, if you have one or more of the starter assemblies, let me know what you're looking for. Also have a little green paper.
Have some stuff to trade, if you have one or more of the starter assemblies, let me know what you're looking for. Also have a little green paper.
I didn't have time to get your stuff out today. The rubber handle on mine is decent except for a couple small cracks.
I'll just send you the entire saw, minus the starter cover, carb, and front handle. If anybody needs parts off it, just pass on the favor.
AU_K2500
NSM
Aaron, Ive got your parts sitting in front of me, and if i remember I will stop by the PO in the morning, if i forget it will be around 2. Either way it will go out priority tomorrow to you. Hope it helps.
I didn't have time to get your stuff out today. The rubber handle on mine is decent except for a couple small cracks.
I'll just send you the entire saw, minus the starter cover, carb, and front handle. If anybody needs parts off it, just pass on the favor.
Thanks so much. Shipping shouldnt be too bad if you ship it parcel post, Just let me know how much.
I may be interested, how much?
Anyone have a starter screen to fit a McCulloch 1-50? I believe several different models like the 1-40, 1-50 and 250 will work.
As far as I know, which definitely isn't every Mac every made, any starter screen that remotely resembles the one that fits that saw will fit it. I haven't seen a metal Mac screen with that screening pattern that won't fit it. Heck, one off of a 125 will fit if I remember correctly.
AU_K2500
NSM
Anybody got any spare Mac 3-25 parts. looking for a bar, and a gas tank, or just all the parts that bolt on the bottom of the tank. the primer and the diaphragm.
Whos a good source in the Forum for Mccullochs and 3-25's?
Whos a good source in the Forum for Mccullochs and 3-25's?
I have a new 3/8" 7 tooth Sprocket for:
Homelite: 350 150 EZ EZ 250 SUPER EZ VI-123 XL-101
Homelite: 350 150 EZ EZ 250 SUPER EZ VI-123 XL-101
