MechanicMatt
Cut Split Stack Burn
AND….
My 7-08 still isn’t living up to it’s potential….
My 7-08 still isn’t living up to it’s potential….
Scrounging Firewood (and other stuff)
- Thread starter mainewoods
- Start date
Help Support Arborist Forum:
It starts with research (any load data or recommendations from companies or individuals or articles). Hodgdon Reloading Data is my primary source and is free online.
Based on this information, I try to identify one or more good powders, hopefully that I already have. I often look to find a powder that will provide near maximum velocity at less pressure than other powders in that cartridge. That allows me to start near maximum velocity with less worry. In recent years, I have also been shifting to powders that I can "throw" accurately, instead of weighing every charge (like using H-380 instead of IMR-4350). This saves me a lot of time, and these powders are also often less expensive.
My current favorite powders:
223 - H335
30-30 - LVR
308 - CFE223
270 WSM and 348 (250 gr bullet) StaBALL6.5
30-06 and 338-06 - H380
Next is picking a bullet and determining the correct seating depth. The magazine may be the limiting factor, but if not, I usually try to load the bullet as far out as possible w/o touching the rifling. I start by seating the bullet long, then keep going a bit shorter till the bolt closes easily. I have never found it necessary to crimp bullets, even in my lever guns, so I don't. If your dies are good, your bullet should not move under recoil.
Next is going to the range and seeing how it shoots. If good I go with it, if not I try changing the powder charge, or the bullet, or the cartridge length. Some guns prefer a max (or near max) charge, others get best accuracy with a slightly reduced charge. You will not know till you experiment. Since I'm looking for hunting loads (not target loads) I will usually change the powder charge 1/2 grain at a time and like to use round #s whenever possible. But sometimes, especially when close to max loads, I will go with tenths.
So basically, it is just common sense and hard work! (Adjusting dies and determining if your gun likes full length or neck sizing is a whole new discussion)
You should ALWAYS ensure that your ammo fits and feed right in your magazine, and that it chambers easily and smoothly in your gun. The ammo I load is specific for each individual rifle, not just for any rifle of that caliber.
You may recall last year I reloaded my 3 different 30-06 rifles, and each one preferred something different (all had 22" barrels with 1 in 10 twist).
My Rugar American Rifle shoots very well (and to the same point of aim) with 58 gr of IMR 4350 over a magnum primer w/168 gr Barnes TTSX or 57 gr H-380 (standard primer) and 165 gr Speer BT.
Your Dad's pre-64 Model 70 Featherweight preferred the charge reduced to 56 grains of H-380. It shot both bullets well, but groups were about 2" apart, so we just loaded the Barnes TTSX bullets.
Your post-64 Model 70 Stainless did not like the Barnes bullets but shot the Speer 165 grain BT well with 56.5 gr of H-380.
All 3 of these rifles will be going up with us tomorrow. Your Dad will be using his Featherweight, your nephew will be using your Stainless and my Ruger American Rifle will be a backup rifle in case anyone has any problems.
I also try to use ball power when I can. One thing, when working with 6mm Rem and 22-250 I found necking closer to the lands would make the bullet strike higher. Every caliber and chambering has a sweet spot for bullet weight, speed, and bullet drop like 22-250 is 55g bullet weight, 222/223 50g, 6mm Rem and 243 win is 85g. 25-06 100g.
The ballistic advantage of matching bullet weight and speed in a caliber for flat trajectory is where I normally start. I look for a bullet weight and performance that best fits the game I am hunting. My favorites have always been nosler solid base, you could shoot a lighter bullet for better trajectory and get the same performance that you get with a heavier weight bullet.
I meant to say I have 15k of each type of primers. SPP, SPM,SRP, SLP. Not so many shotgun but still a couple of sleeves of Cheddite I saw for a good price on sale online somewhere. I just started loading shotgun so that Promo is going to come in handy.
Mine sure fits the spot between my 30-06 and 416 Mag. No real need for it but I like it anyways and I can feed it squib loads with 357mag lead for plinking.
Never heard a squib being a positive thing
.
I drove a white 1992 New Yorker for a couple years. Mine had an all blue interior with plush velour upholstery. That was the epitome of 90s big three "luxury". Drove like a boat but it sure was nice on the highway. Popped my favorite cassette in the radio and just cruised.
The old Nosler solid base used to be my favorite, but when they went with ballistic tips they got too soft (IMO).
I find the Barnes copper bullets to be very dependable. Never got the original TSX to shoot well but had much better luck with the TTSX in 30-06, 300 Win Mag and in my 338-06. My 270 WSM likes the 129 grain Barnes LRX, which has a VG BC. I also like that they don't ruin as much meat as many conventional bullets. Was able to salvage a lot more backstrap from last years Buck shot with the 338-06 because of that.
Never heard a squib being a positive thing
Ok. Reduced power load. Lol.
Love it. Nice work!
I get a kick out of the papers on the bulletin board "flapping in the breeze".
Is she reloading for your lever gun? Just seeing the flat/round nose bullet is all.
I don't think that I have ever seen a plug burned back that bad. It is definetly burning oil. I worked on cars and trucks for a living for 10 years back in 70's. Maybe the electrodes are made in China and the plugs assembled here. Time for some better spark plugs.
Could be . Thinking I have a lean condition maybe a bad intake gasket . Not going to look too hard at it since I’m replacing the motor .
When I rebuild this one I’ll look at it closely to determine the cause
Yesterday's fun was more cleaning up of last years fallen trees. Picture one, dead Ash tree.
A few of you might remember this farm implement that I posted about in an Oak tree. Yesterday I cut the Oak down without destroying the implement. I cut a 1 1/2" v notch halfway into the tree in hopes that the tree would bounce off the stump when it came down. My plan worked perfectly. The tree jumped foward a few inches missing the iplement. All the brush got chipped up and the tree got bucked up. It now resides in my splitting pile.
A few of you might remember this farm implement that I posted about in an Oak tree. Yesterday I cut the Oak down without destroying the implement. I cut a 1 1/2" v notch halfway into the tree in hopes that the tree would bounce off the stump when it came down. My plan worked perfectly. The tree jumped foward a few inches missing the iplement. All the brush got chipped up and the tree got bucked up. It now resides in my splitting pile.
Attachments
xraydaniel
Addicted to ArboristSite
Wouldn't notice that at the grocery store. Today was my day off for veterans day, wife had off too, so we did our normal Saturday running around today. $482.57 at Walmart. This did include oil and filters for the truck, her car and the expedition. That was close to $100.00 by its self. The rest was groceries.
Dog food is still up there too. I can't wait till zade is over a year old and can eat the same food at zeke and ziva. $69.99 for a 47lb of puppy food. Just nuts.
Good news, I scored 2 full boxes of vented soffit for $2.00 per piece and 10 pieces of u channel for the same price. Grabbed a few electrical boxes and misc 90* conduit pieces, ta's and connectors for $5.00.
Similar threads
Want to Sell
4 free saws
