Swap meet...

[tlandrum]

i need a 24" bar for a large mount husky and a tank for an ms440.got lots of stihl and husky parts to trade and a wee few dead presidents

 

[Scooterbum]

If you could get one with just a nice cylinder, then I already have a "special" piston to use in your build, that will bump compression considerably (200 psi range.)

Jacob, any specs on that piston?
I have access to a lathe and a bridgeport collecting dust, and a stock 038magII i'm looking to beef up a little.Just looking at all options. Thanks Scoot

 

[TRI955]

i need a 24" bar for a large mount husky and a tank for an ms440.got lots of stihl and husky parts to trade and a wee few dead presidents

I have a like new Husky 24" x .050 and a new Total Superbar 24" x .058. PM me if interested.

Always looking for 181/281/288 parts...

 

[Tree Sling'r]

Anyone have a full-wrap handle for a 372 Huskshizzle?

I have a brand new wrap handle for 372, PM if interested.

 

[Tree Sling'r]

LOL, I apologize, wasnt trying to cut in, but I would be interested in one for sure. After you get yours!

I can make one, make em' daily. Would need to machine some off the base of the cylinder though to compensate.

 

[Kwdog75]

Any one want/need 372xpg parts?

 

[little possum]

Whatcha got Robert?

 

[Kwdog75]

crankcase, fuel tank, carb, and a couple of odds and ends. Watcha need?

 

[parrisw]

Any one want/need 372xpg parts?

crankcase, fuel tank, carb, and a couple of odds and ends. Watcha need?

Umm, I'm interested. Don't know if I got anything you need though? Let me know please.

 

[Kwdog75]

Umm, I'm interested. Don't know if I got anything you need though? Let me know please.

It's not a complete saw Will, just parts.

 

[little possum]

Watcha need?

Need- another saw, like another hole in my head haha
Nothing I dont guess, really need to get these 3 288s straightened out before worrying about another 372. Oh yea, those are all in line behind the 394! haha. Thanks again!

 

[Kwdog75]

Love the 288's, but i have enough project saws on the go now. Have fun!

 

[parrisw]

It's not a complete saw Will, just parts.

Ya, I know. I like parts, to build saws with! I got a box of 394 stuff? You need any of that?

 

[Jacob J.]

Ya, I know. I like parts, to build saws with! I got a box of 394 stuff? You need any of that?

Will, if you have an extra coil I could use one for Jesse's saw.

 

[parrisw]

Will, if you have an extra coil I could use one for Jesse's saw.

Sorry J, got none of those, just used my last one the other day to fix a buddies 395.

 

[Kwdog75]

Will, if you have an extra coil I could use one for Jesse's saw.

If you have a good wire i may have a coil.

 

[Jacob J.]

If you have a good wire i may have a coil.

I have good ignition leads and terminals. I'll gladly buy a coil from you. I'm in the final stages of building Jesse a replacement for the saw that was stolen, and found out today I have two totally dead flat coils.

 

[Meadow Beaver]

Will, if you have an extra coil I could use one for Jesse's saw.

I have one as well if you need an extra-extra coil.

 

[67L36Driver]

Mac Eager Beaver 2.3 wanted.

Mac. Eager Beaver 2.3" (38cc) wanted. Yeah, I know they are ugly.

A.K.A.: models E.B. 2316, E.B. 2318, Silver Eagle 2318, Mac 3818, Pro Mac 3805 and MacCat super 18. (probably others but you get the picture.)

Have Craftsman 36cc w/16" to trade. Model 358.350462 (I don't know which Poulan it is.) Works very good, cut up a coord of green walnut in September. Needs the fuel pick up line replaced someday.

 

[Kwdog75]

I have good ignition leads and terminals. I'll gladly buy a coil from you. I'm in the final stages of building Jesse a replacement for the saw that was stolen, and found out today I have two totally dead flat coils.

i have one left, PM me your address and i send it out to you this Saturday.