Swap meet...

[srcarr52]

I need 1 complete 288 clutch cover. Do you two need anything in particular?

Well I can send you a cover with all the internals but no arm. Maybe jimbo1490 can you or I an arm and I can send him a decent cover.

I only need 394/5 parts or new projects.

 

[srcarr52]

I'm also looking for a bar to fit an Olympic 999f (stihl big mount). I would like to find a 32-36 in 50 gauge for milling.

I have a couple of husky mount Oregon 34" bars that have been refurbished and have new tips.

 

[jimbo1490]

I need chain brake assemblies for 394/395's. Anyone got any of those?

Not a single one, sorry.

 

[jimbo1490]

Well I can send you a cover with all the internals but no arm. Maybe jimbo1490 can you or I an arm and I can send him a decent cover.

I only need 394/5 parts or new projects.

Sounds like a plan. I get one good cover out of my 2 junk ones. The only 395 thing I have right now is a muffler.

jimbo

 

[little possum]

I will retire from the 288 market for a while

 

[Mastermind]

I will retire from the 288 market for a while

You get that brake handle yet???

 

[little possum]

Yes sir, forgot to send you a thanks!

There is a redneck fix for broken corner mounts on the case... I can provide pictures if you dont find anything.

 

[Mastermind]

Yes sir, forgot to send you a thanks!

There is a redneck fix for broken corner mounts on the case... I can provide pictures if you dont find anything.

I'm trying to fine a 288 case for a friend of ours.

The 034 cases I need both had the PTO side bearing insert loose in the case. I'm wondering if this is a common issue on the 034?!?!

 

[jimbo1490]

I'm trying to fine a 288 case for a friend of ours.

The 034 cases I need both had the PTO side bearing insert loose in the case. I'm wondering if this is a common issue on the 034?!?!

Aren't 181/281 cases the same? if yes, I have a nice set.

Jimbo

 

[Mastermind]

Aren't 181/281 cases the same? if yes, I have a nice set.

Jimbo

PM sent

 

[nmurph]

I need a chainbrake/clutch cover for a 5000+. Cosmetics aren't important as this saw is already a 330/5000+ hybrid. Heck, a 490 cover would just about complete it!!
I also need the upper R AV that attaches the top handle to the cylinder. I have the mount, I just need the rubber.

Is there somewhere to buy Partner parts on-line?

 

[nmurph]

I will retire from the 288 market for a while

Did you find a 288 starter pulley?

 

[srcarr52]

Sounds like a plan. I get one good cover out of my 2 junk ones. The only 395 thing I have right now is a muffler.

jimbo

I do need a good muffler and brace if you got it. Send me a pm with your adress and I'll send you a 288 cover with everything minus the arm.

 

[Arrowhead]

Still looking for a decent piston and air filter cover for a Homelite Super XL Auto.

 

[timberdollars]

Poulan micro

Lookin for a Early Micro S25cva cylinder, maybe piston too, Bought a piece o **** off eBay, Looks great not to many scratches but PO ran starting fluid in it to test it instead of changing fuel line.
I'm into this saw too much now, My eBay luck is going down hill fast (last 4)
I don't want to keep buying $50.00 parts saws looking for a good PC

 

[jimbo1490]

Lookin for a Early Micro S25cva cylinder, maybe piston too, Bought a piece o **** off eBay, Looks great not to many scratches but PO ran starting fluid in it to test it instead of changing fuel line.
I'm into this saw too much now, My eBay luck is going down hill fast (last 4)
I don't want to keep buying $50.00 parts saws looking for a good PC

I have a couple of these in perfect shape. All I have to do is find them :msp_rolleyes:

Jimbo

 

[srcarr52]

Lookin for a Early Micro S25cva cylinder, maybe piston too, Bought a piece o **** off eBay, Looks great not to many scratches but PO ran starting fluid in it to test it instead of changing fuel line.
I'm into this saw too much now, My eBay luck is going down hill fast (last 4)
I don't want to keep buying $50.00 parts saws looking for a good PC

The Poulan Micro was a 2.1 ci /34 cc cylinder where the S25DA/CVA were mostly 2.3 ci / 38 cc cylinders. I don't know if the large 38 cc off a S25 will fit on the Micro but if it does it will certainly give it a little more zip.

 

[tbone75]

The Poulan Micro was a 2.1 ci /34 cc cylinder where the S25DA/CVA were mostly 2.3 ci / 38 cc cylinders. I don't know if the large 38 cc off a S25 will fit on the Micro but if it does it will certainly give it a little more zip.

I have one of each tore down.Think I will just find out?As soon as I get time? :hmm3grin2orange:

 

[Eccentric]

Still looking for a decent piston and air filter cover for a Homelite Super XL Auto.

When you posted in the Homelite thread a couple of weeks ago, I offered you a used AF cover for the cost of shipping. You never got back to me. Missed my post maybe? Still yours if you want it. Used black plastic cover from an SXL-AO.

The Poulan Micro was a 2.1 ci /34 cc cylinder where the S25DA/CVA were mostly 2.3 ci / 38 cc cylinders. I don't know if the large 38 cc off a S25 will fit on the Micro but if it does it will certainly give it a little more zip.

I have one of each tore down.Think I will just find out?As soon as I get time? :hmm3grin2orange:

A 25/S25 cylinder won't work on a micro family saw (even though some of the micros have "XXV" and "25" in their model name). There were some 38cc micro family saws late in the series (Sears 2300 being one of 'em). Somebody posted the part #s for the 38cc micro series piston assembly and jug a while ago in the Poulan thread. They were still available from Poulan, and not too pricey IIRC. They're also the bare piston/chromed cylinder type, while most micros have chromed pistons and bare bores...

 

[Duke Thieroff]

Looking for a chain tensioner for a Husky 268, the followingmodels will fit
161, 181, 266, 272

Also looking for an air filter the following modes wll fit
262, 268, 261, 272, 394



Thank you

Chris