Sure is quiet in here....do I need to start a fight?

[farrell]

Think we invented ice fishing.

It's an unfriendly sport

 

[tbone75]

Haven't been able to ice fish round here in years , never froze thick nuff. We could up till bout 10 yrs. ago , not no more ! Maybe this year ?

 

[nk14zp]

Hey slakerz this was on page two again.

 

[Cantdog]

Hey slakerz this was on page two again.

We hate page II.......was almost there again.....fair amount of traffic on the site today....

 

[tbone75]

I was busy ! Fuel lines on a 235 Husky . Stupid thing , gotta take the whole handle off to get to the carb and fuel lines !

 

[Cantdog]

I was busy ! Fuel lines on a 235 Husky . Stupid thing , gotta take the whole handle off to get to the carb and fuel lines !

Yep those saws are a real pain to work on......had to do impulse and boot on a 335....a couple yrs ago....had to take the entire motor out of the frame.....not an easy thing to do on that tiny little thing.....all had to be done in the correct order...exactly....

 

[tbone75]

That just plain sucks Robin ! Maybe I should just stay away from them things !!

 

[Cantdog]

That just plain sucks Robin ! Maybe I should just stay away from them things !!

All those, I think are a Stihl design........LOL!!! Surely just as convoluted design as any Stihl I've had to fuss with!!!

 

[dancan]

Eeeeeeeeeeeelux

 

[tbone75]

All those, I think are a Stihl design........LOL!!! Surely just as convoluted design as any Stihl I've had to fuss with!!!

Some Steel beergeneer jumped ship and went to Husky !

 

[turbo885]

I was busy ! Fuel lines on a 235 Husky . Stupid thing , gotta take the whole handle off to get to the carb and fuel lines !

Are you sure there isn't a little panel there you can take off and get to the carb I am thinking there is just a couple screws

 

[tbone75]

Had to take the handle off to get to that little panel off. Just one screw holds it on. But its behind the handle.

 

[turbo885]

I remember there was something there it has been awhile they do suck to work on I didn't forget that

 

[Icehouse]

I have only worked on one clam shell saw, it was a little Stihl I found by the county dumpster. Took it apart just to see what was inside, not knowing what I was doing it took quit a while, but did seem like it would be hard to get to anyone part. Good luck Tbone I know you will prevail.

 

[tbone75]

Them little Steels can be a pain until you have done a few ! Not so bad after you get use to them. LOL

The little Husky is running good again ! Hope I don't get use to them ! LOL

 

[pioneerguy600]

It's an unfriendly sport

Its actually a very friendly sport, the way we do it.

 

[tbone75]

I could handle fishing inside like that ! LOL

 

[farrell]

Its actually a very friendly sport, the way we do it.

Well Jerry............that's cheating!

I done it in the middle of February on Lake Erie when the air temp was around zero and there was a 30 mph north wind

Fishing for steelhead and no shelter

 

[Stihl 041S]

Lunch time!!!

 

[turbo885]

I have only worked on one clam shell saw, it was a little Stihl I found by the county dumpster. Took it apart just to see what was inside, not knowing what I was doing it took quit a while, but did seem like it would be hard to get to anyone part. Good luck Tbone I know you will prevail.[/quote

Actually I don't mind the stihl clamshells I snatch every one up I can find once you get used to them they don't take any longer than anything else