Sure is quiet in here....do I need to start a fight?

[roncoinc]

I like corona!

What's it to ya?

I don't go around dissin your beer of choice


Sent from my iPhone using Tapatalk

Thats cause Dan dont drink " choice " beer !!

 

[pioneerguy600]

Thats cause Dan dont drink " choice " beer !!

I agree, Dan drinks the beer of choice instead!!

 

[tbone75]

Yes it finally got used and I was not the one to christen it. Scott AKA Big Red , who is a Pro meat cutter had the honours, durn near had to wrestle him to get that knife back from him. That guy is so fussy about what knife he uses to cut with that he tests each one to see if it cuts hair off his forearm just so, no sliding the knife back n forth or anything. Just has to cut like a razor or he won`t cut with it....LOL

Musta been sharp . LOL

 

[dancan]

Ifn ah gots te puah lemmon in te drink it .......
I'll stick with choice beer LOL

 

[tbone75]

Got to go drill a couple holes , these black pearl grips don't fit muh dang gun right ! They is gonna real quick ! LOL

 

[roncoinc]

I agree, Dan drinks the beer of choice instead!!

And he aint very good at choosin !!

 

[pioneerguy600]

Musta been sharp . LOL

I polish the cutting edge on fine ceramic rods, have 3 sets of rods set like a crossed X but at about 15 degrees either side of center. Gets a knife sharp enough to shave with,couple strokes on the razor strop and a drop of oil, its ready to put into its sheath and will cut.

 

[dancan]

And he aint very good at choosin !!

I guess .... Look at my hang out .....

 

[pioneerguy600]

Ifn ah gots te puah lemmon in te drink it .......
I'll stick with choice beer LOL

Vile fruit!! Remember the angry Scotsman and the Keiths beer commercial?

 

[dancan]

I like my hangout

 

[pioneerguy600]

And he aint very good at choosin !!

Beer of choice is just like Stihls, must be the best.

 

[pioneerguy600]

I like my hangout

Got any bar oil , Dan?

 

[dancan]

[video=youtube_share;8VXN3yFCk-U]http://youtu.be/8VXN3yFCk-U[/video]

Sorry John

 

[dancan]

[video=youtube_share;H15xBHqPDZE]http://youtu.be/H15xBHqPDZE[/video]

Sorry John

 

[dancan]

[video=youtube_share;7ZiabUfQT1g]http://youtu.be/7ZiabUfQT1g[/video]

Sorry John

 

[pioneerguy600]

[video=youtube_share;8VXN3yFCk-U]http://youtu.be/8VXN3yFCk-U[/video]

Sorry John

That`s the guy!!!...LOL

 

[dancan]

[video=youtube_share;YPMAm3Un8bk]http://youtu.be/YPMAm3Un8bk[/video]

Sorry John

 

[farrell]

.

Alright let's start with this.......

I'm assuming it's an EPA and it's newer so......

It should be a 45mm piston single ring

The older 350's had a smaller piston single ring 44mm I believe

Do what you want to muff......gut it, drill holes, replace

My 350 is an EPA model and I removed the limiters off carb, removed heat shield, removed base gasket, drilled some holes in the muff not much else to worry bout with them

 

[BigDaddyR]

Alright let's start with this.......

I'm assuming it's an EPA and it's newer so......

It should be a 45mm piston single ring

The older 350's had a smaller piston single ring 44mm I believe

Do what you want to muff......gut it, drill holes, replace

My 350 is an EPA model and I removed the limiters off carb, removed heat shield, removed base gasket, drilled some holes in the muff not much else to worry bout with them

What does removing the heat sheild gain ya? Less weight or not needed due to less heat with no cat in muffler? Less weight?


Rick

 

[farrell]

What does removing the heat sheild gain ya? Less weight or not needed due to less heat with no cat in muffler? Less weight?


Rick

Not sure it gains anything

My thot was without it lets more air in around cylinder there for stays cooler

Ron's thot was it reflex heat from muff away from cylinder

Both make sense


Sent from my iPhone using Tapatalk