Sure is quiet in here....do I need to start a fight?

[tbone75]

I bet media cat might help when building a saw up from parts?

Any idea how hard it is to find covers, carbs, and such for the 044?

Say, if I started with case, crank, rod, rear handle, and tanks, would I have any trouble finding the other parts needed to make one?

Nah , only hard to find part is a good tank.

Another thing to look for on them is the angled fin jug ! That is the best one ! Came on the older 10mm saws.

 

[farrell]

Man I hurt from yesterday runnin the brick (268) in those 36"+ maple!

My buddies shinny 757 I ported was runnin great!

I had to sharpen it cause no one else seems to be able to and do a lil tuning on the carb

That freaking saw is deafening loud!

 

[tbone75]

044 saws , serial # 29583701 and below were 10mm saws. Above are 12mm wrist pin.

 

[tbone75]

Man I hurt from yesterday runnin the brick (268) in those 36"+ maple!

My buddies shinny 757 I ported was runnin great!

I had to sharpen it cause no one else seems to be able to and do a lil tuning on the carb

That freaking saw is deafening loud!

To bad your 372 is down !

 

[tbone75]

Thanks Geoff!

It would be a cryin shame to have to replace a monkey topend

:ah:

 

[farrell]

When was the last time you went thru the carb ??

check the fuel screen inside and stiffness of metering diaphragm.

make sure low jet is clear,can be done on saw.

I haven't done anything to this saw since I got it from John

Except clean it after using it

Yesterday was the first time I touched carb settings on it

 

[farrell]

Sure easy on a Husky !

Yes it is!

 

[farrell]

To bad your 372 is down !

No kidding!

I miss her!

But the 268 is a fine running saw!

 

[IEL]

If I get a good chance, I will try talkig to the boss about it.

I was telling him about some of my older saws, and he thought that was the coolest thing!

Sounds like he might want to see one or two of them?

 

[tbone75]

I haven't done anything to this saw since I got it from John

Except clean it after using it

Yesterday was the first time I touched carb settings on it

I never adjusted anything on it. Just as the Monkey sent it . LOL

 

[tbone75]

No kidding!

I miss her!

But the 268 is a fine running saw!

My 266 will eat your 268 ! :msp_w00t:

 

[tbone75]

If I get a good chance, I will try talkig to the boss about it.

I was telling him about some of my older saws, and he thought that was the coolest thing!

Sounds like he might want to see one or two of them?

Good tanks go for around 75.00 ! Make yerself a few bucks off them,if you find any ? LOL

 

[Jimmy in NC]

Gabby bunch here....I'm head in to the shop for a few hours. Try to get the trimmer done and ready to list. Tired of sitting on the couch sniffling...I will sit in the shop and sniffle for a bit!

Sent from my MiniMac on E-10.

 

[farrell]

My 266 will eat your 268 ! :msp_w00t:

Blah blah blah

When did we start measuring man hood?

 

[tbone75]

Blah blah blah

When did we start measuring man hood?

I just like showing it off ! The saw that is ! LOL Not much else to show off ! :msp_tongue:

That saw is just crazy wild ! LOL

Thanks Smurf !

 

[tbone75]

Gabby bunch here....I'm head in to the shop for a few hours. Try to get the trimmer done and ready to list. Tired of sitting on the couch sniffling...I will sit in the shop and sniffle for a bit!

Sent from my MiniMac on E-10.

I can go play in the shop today too ! Just very light duty ! LOL

 

[farrell]

I can go play in the shop today too ! Just very light duty ! LOL

I got to go to the shop too!

12hr day ahead

Push green button!

 

[IEL]

Does anyone know why there are new ms460s on ebay for $1800?
I cant figure out why you would pay $1000 more on ebay than at the dealer....... LOL

 

[tbone75]

Does anyone know why there are new ms460s on ebay for $1800?
I cant figure out why you would pay $1000 more on ebay than at the dealer....... LOL

Haven't seen that ? LMAO !! But if someone will pay it ? No way its worth that !!

 

[tbone75]

I got to go to the shop too!

12hr day ahead

Push green button!

Good luck !